UV LED versus UV Lamp Lifetime short or long? Some of systems using UV LED, the lifecycle up to 15,000 to 20,000 hours while UV Lamps only can last up to 1,500 hours.

UV LED can last longer than UV lamps due to the following reasons:

1. Different technologies: UV LED uses solid-state technology while UV lamps use a gas discharge mechanism, which is subject to wear and tear over time.

2. Better heat management: UV LED has a lower heat output compared to UV lamps, reducing the strain on the system and extending its lifespan.

3. Efficient use of energy: UV LED is a more efficient use of energy compared to UV lamps, which can result in longer lifespan.

4. Durability: UV LED is a solid-state device that is less prone to physical damage compared to UV lamps, which are more fragile and prone to breaking.

In addition, the long lifespan of UV LED makes it a more cost-effective solution over time, as it requires fewer replacements and less maintenance compared to UV lamps.

UV LED versus UV Lamp Lifetime short or long?

Number of times the light is turned on and off

The number of starts is the number of times the light is turned on and off completely. The pressure in the lamp medium changes when the lamp is operating at full capacity, which puts mechanical stress on the lamp. Other mechanical stresses are caused by thermal cycling of lamp components. Another reason why the number of starts affects the life of the bulb is the introduction of tungsten and small amounts of other materials from the electrodes each time the lamp is ignited.

This pollution when introduced into the lamp environment can effectively increase the open circuit voltage of the lamp, making lamp operation more difficult. If possible, start the light at high power to reduce the time the light is in start-up mode. Note: Starting too much will cause premature darkening of the tip and reduced yield.

UV LED versus UV Lamp Lifetime.

How to increase the lifespan of UV LED versus UV Lamp Lifetime

Keep the reflector clean
Make sure the reflector is not deformed by heat from the lamp
Clean dust and dirt from the fan blades that obstruct airflow and reduce cooling efficiency.

How to install lights properly?

Proper UV lamp installation for UV LED versus UV Lamp Lifetime to enhance the working life:

Avoid getting your fingers oily on the lamp body by using a tissue or gloves. Use alcohol wipes to ensure the surface is clean.
Maintain good electrical connections.
Allows flexibility in installation. The lamp is not held tightly in place. This can limit movement as the reflector expands and contracts during operation.

Leci - Reputable parts repair and replacement unit

UV lamps are being widely used in many manufacturing fields. However, currently there are still not many units with enough capacity to carry out warranty and repair of reputable components and machinery. Machine repair requires technical staff to be experienced, skilled, and meet standard inspection procedures so as not to affect the machine.
Reasons to choose LECI to replace and repair uv bulbs:

• Professional technician team: LECI's current technician team has more than 15 years of experience and used to be chief engineers of many large enterprises in the industry today.
• Support for timely replacement of components for machine models: LECI always has a stock of genuine components for high-frequency presses, helping customers promptly repair and replace components without interrupting production.
• Ready to advise customers 24/24: LECI is always ready to support and advise customers anytime, anywhere to promptly fix problems as quickly as possible.
• The word "trust" is the top priority: With the words "heart" and "range" LECI is committed to bringing the best quality of services and products to its customers.

There are many names on the market that provide components and repair equipment. This brings diversity in choice for customers but somewhat causes difficulty and hesitation when not knowing which brand is good. So let's get right to LECI.
LECI is a unit specializing in providing components and repairing wood chip presses, wood joiners, high frequency presses... favored by many large partners.
Our products are distributed genuine from reputable companies in the world such as: China, France, USA, Singapore, with big brands such as Lichtzen (Korea), II-VI and Hybertherm from the USA .
Quality products, reasonable prices, professional technical team, dedicated consulting support and perfect service quality are things that customers can be completely assured of when coming to LECI.
Whether you are looking for electronic tubes, high frequency devices, high frequency machine components, high frequency light bulbs... LECI can meet your needs with the spirit of continuous improvement, updating techniques and materials. materials, design. Industry-leading equipment, delivering the best value to customers and the market.

Contact and order (24/7)

LECI Co., Ltd
R-1901, Saigon Trade Center Bld, 37 Ton Duc Thang Str., Ben Nghe W., Dist. 1, HCM City 70000, VN.
T: +842822202988 | F: +8428222 02989

Hotline: (+84) 0901442689 (Whatsapp)
Website: www.lecitubes.com